logo
Chào mừng đến ESTEL (GUANGDONG) TECHNOLOGY CO., LTD.
+8613752765943 / 86-0755 23592644

Solving Cable Management and Thermal Issues in a Coastal Wireless Access Node

2026/11/16

Tin tức công ty mới nhất về Solving Cable Management and Thermal Issues in a Coastal Wireless Access Node

Solving Cable Management and Thermal Issues in a Coastal Wireless Access Node

 

 

Background

 

A wireless internet service provider (WISP) was expanding its coverage along a coastal highway. The deployment required outdoor enclosures to house point-to-point radio units, access switches, and fiber termination equipment. The sites were fully exposed to salt spray, high humidity, and intense afternoon sun.

 

Initially, the provider used standard galvanized steel cabinets. However, within a year, field technicians reported two recurring problems: corrosion around the cable entry points and disorganized cabling inside the enclosures. The cable chaos not only made maintenance difficult but also restricted airflow, causing the radio equipment to overheat during peak summer months.

 

 

The Challenge: Corrosion, Cabling, and Heat

 

The operator identified three specific issues that needed to be resolved.

 

1. Corrosion at the Enclosure Level


While the cabinet shell held up reasonably well, the cable entry points became the weak link. Salt-laden moisture entered through the cable glands, leading to corrosion on the internal grounding bar and the switch chassis. The steel cabinets were also heavy, making installation on elevated concrete pads difficult for the small installation crews.

 

2. Cable Management and Airflow


As more equipment was added—additional switches, a patch panel for the fiber links—the internal cabling became dense. The lack of a structured cable management system meant that power cables and data cables were tangled. This blocked the passive airflow and made it hard to trace a specific link during troubleshooting.

 

3. Visibility and Maintenance


The sites were remote. Technicians often arrived at night or during poor weather. The cabinets lacked internal lighting, and there was no way to monitor if a door was left open or if the internal temperature was rising too high.

 

 

The Solution: A Purpose-Built Aluminum Enclosure

 

The provider replaced the problematic steel cabinets with a 32U outdoor aluminum cabinet designed specifically for access network deployments.

 

1. Aluminum Construction and Sealing


The new cabinet uses a double-wall aluminum structure. The aluminum alloy provides inherent corrosion resistance, which is critical in coastal environments where salt spray is constant. The double-wall design—2.0 mm outer shell and 1.0 mm inner panel—includes 20 mm of PEF insulation. This insulation reduces heat transfer from the sun, keeping the internal temperature more stable. The cabinet is rated IP65, ensuring a tight seal against dust and water.

 

2. Structured Cabling and Airflow


To address the cable chaos, the cabinet was equipped with a 1U 24-port CAT6A patch panel and a horizontal cable manager (24-finger). This allowed the technicians to route the fiber and copper links neatly, separating data cables from power cables. The organized layout improved airflow within the cabinet, reducing hot spots and keeping the radio units cooler. The bottom cable entry design, with multiple 22.5 mm openings, allowed for clean routing without compromising the seal.

 

3. Maintenance and Monitoring Features


The cabinet includes dual AC 230V cooling fans with a temperature controller. The fans adjust their speed based on the internal temperature, providing cooling when needed and reducing noise and dust ingress when not required. For maintenance, the cabinet is equipped with dual LED lamps, providing illumination inside even at night. Dual door sensors were installed to monitor access, alerting the network operations center if a door is opened or left ajar.

 

 

The Results

 

After the upgrade, the operator observed a significant improvement in site reliability and maintenance efficiency. The aluminum construction eliminated the corrosion issues at the cable entry points. The structured cabling system reduced the time required for troubleshooting, as technicians could quickly identify and trace specific connections. The internal temperature remained stable even during peak summer, reducing thermal-related equipment failures.

 

The combination of the temperature-controlled fans and the insulated aluminum structure proved effective in maintaining a stable environment without the need for a compressor-based air conditioner, which reduced the overall power consumption of the site.